raingutter regatta sail tips

orji March 19, 2022 raingutter , regatta , sail Comment

Too high and your boat will. Instead they should.

Make An Award Winning Raingutter Regatta Trimaran Boat Kit By Michael Spitler Michaelspitler

A bent rudder will steer the boat into the raingutter.

. Push the sail down the mast as far as it will go. Michael Spitler has some great fresh ideas on design click through. The bottom edge of the sail needs to be about 12 inch above the deck of the boat.

When the starter says go the boys will propel the boats by blowing on the sail with the straw provided. Trim excess weight off everything and be careful how much you add like decorations and paint. LET THE BOYS DO IT.

The boy may use his hand only to upright his boat or to remove an impediment ie. The event requires cub scouts to build a sail boat utilizing the parts contained in the official bsa raingutter regatta trimaran kit. If the sail is too low the corners rub against the gutter or dip in the water.

Position the sail on the mast. If the sail was too high the boat was top heavy and tended to tip over. Lower the sail so that it touches the deck.

Google raingutter regatta for boat ideas and construction tips. Special thanks to the other. He researched many videos and made his own version of the winning regattas.

The starter stands at the opposite end with hands raised. If the sail is too low the corners rub against the gutter or dip in the water. Position the sail on the mast.

Trim the hull to make it symmetrical. About 34 from the top of the mast either glue the sail to it or attach securely with tape. If the sail was too high the boat was top heavy and tended to tip over.

The race is open to all tiger cubs cub scouts and webelos scouts registered to. Vinyl gutters are better because they wont bend. The vertical position of the sale is important.

The hull is 2 12 wide and the sail is 2 12 wideThe hull is made of Dow Corning Styrofoam. Ensure the rudder is flat. Standard BSA kit construction tips.

Fold the sail toward the back of boat along the two red lines so that it does not extend past the outriggers. If youre not sure of what this raingutter regatta exactly it is a quick video. As our Raingutter Regatta race gets closer here are a few pages that have some cool tips on boat making.

Sail must be upright for its entire length and must be attached to the mast supplied with the kit. Sail touches hull 2. Boat building Boats must be constructed from the official BSA trimaran kits distributed by the pack.

These Raingutter boats can be built the same day they are raced or taken home to build or built as a group during a meeting. Everyone must demonstrate good sportsmanship. Supplies to Build Boats.

How to Make Recycled Raingutter Regatta Boats. An area to show off your decorations is on the sail. If the sail was too low the corners rubbed against the gutter or dipped in the water.

Raingutter Regatta Tips Pack 410 1. The boats are propelled by boys blowing into the sails. The sail may be tied tacked or glued in place as long as it is upright and unfolded.

Fold sail to rear 1. When he drops his hand the boys begin to blow. Zaiden builds his Rain Gutter Regatta for Cub Scouts.

Contrary to popular belief the balsa pontoons should not have a V-shaped keel. Cup sail modifications will be faster than the standard sail Appendix B. Boats must be made from the official BSA Raingutter Regatta Trimaran Boat Kit.

Start with the boats stern touching the end of the rain gutter. For each type of. Each Rainspout Sailboat kit comes with 1 hull 1 mast 1 rudder and a sail.

The traditional Raingutter Regatta uses 10 gutters with end caps attached. The bottom edge of the sail needed to be about 12 inch above the deck of the boat. This is done by attaching a thread to the lower corners of the sail and pulling them back.

The bottom edge of the sail needed to be about 12 inch above the deck of the boat. You do want to glue your sail in placeat the very minimum and having flat rails on the bottom helps. This prevents dragging on the gutter sides.

NO substitutions are allowed OutriggersHull. The boats sailed best if they were balanced with more weight to the rear. All parts 2 outriggers polymer hull mast sail and 4 screws provided in the kit must be used in the boat construction.

Use a bit of glue or tape on the mast and sail so they dont come out or spin when blown on. About 34 from the top of the mast either glue the sail to it or attach securely with tape. This minimizes tipping when you blow during race Mast in front of Mast sail behind sail 1.

Once the race is started the boys may not touch the boats with their hands. This is an excellent place for decals and stickersboys love both. The threads are then tied to a straight pin that is inserted in the middle rear of the boat.

Tips from Raingutter Regatta. Attach bottom of sail in a similar manner. The sail provided in the BSA.

How to Build a Raingutter Regatta Boat for Boy Scouts. This helps keep the sail from touching the sides of the raingutter as well as providing stabilization of the sail as it catches the air. The bottom edge of the sail needs to be about 12 inch above the deck of the boat.

Attach bottom of sail in a similar manner. The boys should do the majority of the design and work sandpaper can be used to shape the hull and no power tools should be required. The Outriggers must be no longer than 7 or shorter than 6 ½.

The boats sailed best if they were balanced with more weight to the rear. Cub Scout Trimaran Tips Raingutter Regatta Pack 3 Old Greenwich. The mast may be placed in any position on the top of the boat and the sail may be arched or curved in one dimension only.

Raingutter Regatta Rules and TipsHints Sheet. Be sure to keep these important points in mind while you build your boat. Glue sail to deck.

The boy must hold it there with one hand. If the sail was too low the corners rubbed against the gutter or dipped in the water. Only Official BSA Raingutter Regatta kits are to be used.

If the boat is stuck on the gutter. Scouts can not touch your boat during the race. If you have not received a kit please contact your den.

Each boat must start with the back of the boat touching the end of the rain gutter. Here are a few speed tips to put you in front of the pack. The boys and an adult should make the boat together.

This foam is a closed cell foam. They can only blow the sail. Nothing may extend past front point or rear point of outriggers so maximum total boat length is 6 34 inches Maximum boat hull width not counting sail is 3 38 inches if you have parts sticking out from sides you will hit the gutter and go slow Must use all parts from kit 2 outriggers trimaran hull 4 screws mast and sail No.

Make The Ultimate Raingutter Regatta Racer Scout Life Magazine